[ Pobierz całość w formacie PDF ]
.ft.lbs.)(4) Move the seat to its fully rearward position, if " Seat adjuster to floor pan screws - 29 N·m (20 ft.possible.lbs.)(5) Disconnect and isolate the battery negative " Seat cushion side shield screws - 2.2 N·m (20 in.cable.lbs.).(6) Remove the single screw that secures the front ofeach of the two seat tracks to the floor panel (Fig.4).POWER RECLINER ADJUSTER AND MOTOR(1) Move the seat to its fully forward and fullyraised positions, if possible.(2) Remove the three screws that secure the out-board seat cushion side shield to the seat cushionframe and pull the shield away from the seat cushionfar enough to access the power recliner adjusterlower bracket.(3) If possible, adjust the seat back with the powerrecliner switch far enough to access both of the twoscrews in the power recliner adjuster lower bracket.(4) Disconnect and isolate the battery negativecable.(5) Remove the two screws that secure the powerrecliner adjuster lower bracket to the seat cushionframe (Fig.5).Fig.4 Power Seat Remove/Install - Typical(7) Tilt the seat rearward and unplug the powerseat wire harness connector located on the floorbelow the seat cushion.(8) Remove the seat and adjuster assembly fromthe vehicle.(9) Remove the three screws that secure the out- Fig.5 Power Recliner Adjuster Lower Bracketboard seat cushion side shield to the seat cushionRemove/Installframe and pull the shield away from the seat cush-(6) Remove the inboard seat back pivot screw.ion.(7) Unplug any wire harness connectors between(10) For the driver side front seat only, if the vehi-the seat back and the seat cushion, the number ofcle is equipped with the optional memory seat mod-which will vary with the vehicle equipment.ule, the memory seat module must be removed fromZJ POWER SEAT SYSTEMS 8R - 7REMOVAL AND INSTALLATION (Continued)(8) Remove the seat back from the seat cushionand place it on a suitable work surface.(9) Carefully pull up the side of the seat backcover far enough to access the two screws that securethe power recliner adjuster upper bracket to the seatback frame (Fig.6).Refer to Group 23 - Body for theseat back cover removal procedures.Fig.7 Power Lumbar Adjuster and Motor(5) Disconnect and isolate the battery negativecable.(6) Remove the single screw that secures the frontof each of the two seat tracks to the floor panel.(7) Carefully tilt the top of the seat back towardsthe outboard side of the vehicle.Fig.6 Power Recliner Adjuster Upper Bracket (8) Release the two retainers that secure the mem-Remove/Install ory seat module wire harness to the inboard seatadjuster top rail (Fig.8).(10) Remove the power recliner adjuster and motorunit from the seat back frame.(11) Reverse the removal procedures to install.Tighten the hardware as follows:" Inboard pivot screw - 40 N·m (29 ft.lbs.)" Recliner adjuster bracket screws - 28 N·m (20 ft.lbs.)" Seat cushion side shield screws - 2.2 N·m (20 in.lbs.).POWER LUMBAR ADJUSTER AND MOTOR(1) Remove the power recliner adjuster and motorfrom the seat back frame.See Power ReclinerAdjuster and Motor in this group for the procedures.(2) Remove all of the seat back trim from the seatback.Refer to Group 23 - Body for the procedures.(3) Replace the seat back frame assembly, whichincludes the lumbar adjuster and motor (Fig.7).Fig.8 Memory Seat Module Remove/Install(4) Reverse the removal procedures to install.(9) There are two snap clips that are molded intothe side of the memory seat module closest to theMEMORY SEAT MODULEseat adjuster, which help to secure the module to the(1) Move the driver side front seat to its fully for-riser portion of the stepped mounting bracket.Usingward and fully raised positions, if possible.a trim stick or another suitable wide flat-bladed tool,(2) Remove the single screw that secures each ofreach between the module and the seat adjuster tothe two rear seat track covers to the rear of the seatgently pry each of the two snap clips while pullingtracks and remove the covers.the module away from the mounting bracket.(3) Remove the single screw that secures the rear(10) Slide the memory seat module off of the twoof each of the two seat tracks to the floor panel.mounting bracket slide tabs far enough to access and(4) Move the driver side seat to its fully rearwardunplug the wire harness connectors.position, if possible.8R - 8 POWER SEAT SYSTEMS ZJREMOVAL AND INSTALLATION (Continued)(11) Remove the memory seat module from under NOTE: Following installation, it will be necessary tothe seat cushion.initialize the memory seat module.This is done by(12) Reverse the removal procedures to install.moving each of the power seat adjuster motorsTighten the seat mounting hardware as follows: (including the power recliner and power lumbar" Seat cushion frame to adjuster nuts - 20 N·m (15 motors) through its full range of motion using theft.lbs.) power seat switches.In order to function properly," Seat adjuster to floor panel screws - 29 N·m (20 the memory seat module must  learn the motorft.lbs.).sensor values in each of the adjuster hard stoppositions [ Pobierz caÅ‚ość w formacie PDF ]